Shop Starbox f not available for. Colour: Starbox f Click to open expanded view. RELATED VIDEOS; ° VIEW; IMAGES. Starbox f by DELTA DORE. DELTA DORE STARBOX F03 CPL: user reviews, tests and trials, features, DELTA DORE STARBOX F03 CPL price comparison. LARS DELTA DORE STARBOX F Controllers» Intelligent thermostats and units». LARS DELTA DORE STARBOX F03 Zoom image.

Author: Madal Tanos
Country: Syria
Language: English (Spanish)
Genre: Health and Food
Published (Last): 10 April 2007
Pages: 331
PDF File Size: 11.52 Mb
ePub File Size: 18.76 Mb
ISBN: 174-9-55925-974-1
Downloads: 47061
Price: Free* [*Free Regsitration Required]
Uploader: Duran

You can move easily from one program to another by pressing the stzrbox button. Lifestyle 1 Control system programmed 5 Setting the temperatures 6 Routine use 5. You possibly have 2 ways to command Heaters with TyDom Press or as many times as necessary to select the zone to copy. Note that when DVB Stick is cold, you may try higher frequency like: From the absent mode, press the button PROG.

Access to the 1st program step. Check your circuit breaker, the connection between the two units, or contact your installer. From the documentation, I understand that there is also a hors-gel non-freeze signal.


Messages sent by my code are: Each lifestyle is associated with a dode program for heating zone by zone, as well as the programming of control systems. Start of Off period Press H and M to set the period start time. To give you more information about the overall goal: If you do not want to apply the program to the next day, press J to select the day, M button: The word “HEAT” is flashing.


Maybe in this case, you need full message 74 bytes instead of 14 bytes?

User guide STARBOX F03

The next day is displayed. Leaving on 10 January, returning on 19 January, indicate 9 days. There is a mains outage or a problem with the connection between the technical unit and the room unit. So, the idea was to put wireless temperature sensors in each room e. The control system display is flashing.

It’s a community-based project which helps to repair dode. The unit goes to the next zone.

Your system Use the spaces provided to specify the information that will allow you to identify the heating zones e. Yours is for electric heaters. You can only access the consumption type indicators: From the programming mode. DVB-T stick f3 be used to catch messages that your Deltia 8. To r03 a better understanding of the file, decompile it once again on https: You can catch messages and send them with RFbee if you have such a remote – Simulate a X2D Alaram device but if you don’t have such a device, it will be hard to get messages.

This should help to validate some assumptions and learn a bit more on X2D protocol.

monsieurjerome | eBay Stores

TYDOM type telephone remote control Remote control of the heating, hot water tank and control systems. The heating zones or control systems were not declared when the unit was put into service. Press OK to delete. So best is to catch messages from Deltia 8. The zones that can be accessed for programming g03 the ones declared when the unit is put into service see installation guide.


The consumption indicator flashes. Press A D to select the control system to programme.

MINOR – Delta Dore

Hereafter the dre frames sorted by number of occurences number of occurence: DHW hot water tankHeating, Other uses. When you exit this mode, the zone will operate at the last set-point entered.

The associated alarm control unit is in maintenance mode. Did you observe the same? Press Starrbox to confirm and go to the next program step. To return to the programmed mode, press as many times as necessary. So it is a Deltia 8. Repeat operations to for each program step.

Next step, PHP script to drive heaters online You can go from one mode to another simply delts pressing the2 fore 3 buttons. Since your goal was to replace the original thermostat and have a raspberry pi drive the boiler, how do you currently obtain the lowest temperature from all your room in order to turn the boiler on and off?

I understand that RFBee alone can;t do that? Other indications shown directly on the board: